Build 1.5
The Firechild includes 4 models of the Vari-Mu Compressor ranging from Tube Versions (A/B/C) to a transparent version accurately sampled and emulated from the originals of the 1950s. .
Use this for the Master, or individual tracks, you will be pleasantly surprised!
$35.00
vst3.au.aax | Win – Mac | M1 Supported
* Full version trial for first 15 Days
The Firechild aims to emulate the characteristics of the King of Compressors from the 1950s. The vintage units are variable-mu type compressors, which use the vacuum tubes for reduction of gain right in the audio signal path, (no re-routing to a compression circuit)
Given its primary purpose as a protective device in broadcast or vinyl cutting environments, in which the limiter was required to catch any unwanted signal peaks reliably, these fast attack times were one of the compressors most important features.
Our Plugin features not 1, but 4 models including a “clean version” – off mode for the convolution, which presents a “non-colored” compression characteristics version as well.
The 3 Tube models A/B/C can be driven hard at the input stage without hitting any compression as well, and along with the Bias control, can give the user various Tube Saturation colors, each distinct from the other.
This is produced by actually sampling the real hardware units at multiple stages of gain and compression and implementing it using dynamic convolution technology.
Featuring 6 Release modes, each carefully emulated & sampled from 4 different units each with slightly different electrical components or tubes with different stages of tube life. A Knee control is also provided to further shape the compression characteristics.
Modern Features in the plugin take it way beyond the originals by add adding a full side-chain section with Hp/ Lp filters( 24db/oct) and side-chain gain, as well as a mix knob for mixing the compressed signal with the non-compressed signal. This gives the user a lot of choices in shaping and coloring the sound as they please.
The Firechild sounds great on anything from the Mix Bus, Mastering, Drums & Instruments to Vocals, etc.
The plugin comes with a selection of presets to get you started or design your own from scratch.
Stereo Link:
This switch toggles between the Stereo compressor mode and 2 mono (L-R) compressor modes . Works for stereo channels only.
Model Selector A/B/C/off:
The A/B/C models are emulations of 3 tube versions of the compressor with the tube color and saturation characteristics and features real samples from 3 different hardware models with slightly different electrical components and different stages of Tube life. The 4 model (OFF) features a “transparent “ version of the compressor without the coloration created by tubes.
BIAS:
This controls the bias of the compressor offering additional saturation for all 4 models.
VU Meters:
These indicate the gain reduction for both channels (in stereo mode ) or for the mono channel.
Input Gain:
Ranging from -24dB to +24 dB, the input gain will also saturate the sound of driven hard just like its analog counterpart.
Can be used to saturate the signal on models A/B/C with or without using the compression circuit at all.
Output Gain:
This is the last stage of the signal path and will trim the output signal to -24dB or add gain up to 24dB.
Threshold:
This controls the threshold for the compressor circuit.
Range : +10 to -30 dB.
Knee:
Control the knee curve for the compressor with this control.
Release:
6 fixed release times from the original compressor from fast to slow times.
MIX:
A control to balance the mix of the wet (compressed) signal and the (uncompressed) signal coming from the Model/Convolution Engine.
The Dry signal will carry the processing from Models A/B/C, the off mode has no color characteristics and will produce the absolute dry/original signal.
Sidechain Gain:
This controls the gain of the sidechain signal going into the side chain circuit of the compressor. More gain will cause more compression to occur.
Lp Filter:
The Low Pass filter (range 20 Hz to 20 kHz) filters the side chain signal using a 24 dB / oct Low Pass Filter.
Hp Filter:
The High Pass filter (range 20 Hz to 20 kHz) filters the side chain signal using a 24 dB / oct High Pass Filter.
Sidechain Power:
Toggle between on/off for the side chain circuit.
MAIN POWER:
The bypass switch for the plugin, great from testing “before” and “after” processing.
Tested on:
Plugin Formats:
Minimum System Requirements:
PC/MAC: Windows 10 or later*. / OSX 10.13 or later ( INTEL/M1 Supported ) ( NOT TESTED ON MacOS Ventura* )
Intel i3 / AMD Ryzen or equivalent
2 GB RAM / 300 MB HD
Screen resolution: 1024×768 – VST3, AU, or AAX 64-bit host
Note (a)
M1 Mac users currently using Logic Pro (10.7.2 and above ) or Ableton (11.1) please use ( OSX -M1). All other Daws please use the regular installer ( OSX )
Note (b)
1. SOME ANTI-VIRUS SOFTWARE MIGHT BE ALERT WHILE INSTALLING/DOWNLOADING THE FILES, KINDLY IGNORE THOSE WARNINGS.
Those are False positives. We have tested it on Norton Anti-Virus, and the Installers are clean.
2. FL Studio users may experience the crashing of DAW while using Oversampling feature.
3. Known issues fixed:
– fixed oversampling issues experienced in some daws
– fixed distortion occurring in some systems
– fixed Mode B for balanced LR output
Installation
OSX:
Download the Firechild.pkg file
Double click on the package zip and click open
Follow the instructions to install the plug-in(s)
Windows:
Download the Firechild.exe file
Follow the instructions to install the plug-in(s)
Setup and License Registration:
This plugin uses an online-based license registration system that requires an internet connection. When in trial mode, your computer needs to be online to use the plugin.
Once the plugin is registered, you no longer need to be online to use it. We offer a 15-days trial period for the plugin.
The license registration window allows you to log in to your Tone Empire account directly, and the plugin will automatically authorize if you have purchased it from the Tone Empire site. In case of a purchase from one of our third-party distributors, you can create an account from the website or from the license window of the plugin. Then enter your serial code provided by the third-party distributor (e.g., Plugin Boutique), and the plugin will authorize.
*An internet connection is required.